GE CleanSpeak dryer Error Code F011: Meaning & How to Fix It

By the ErrorCodePro Editorial Team · Last reviewed October 20, 2026

GE CleanSpeak dryer error code F011 means: Dry load. The controls detect that a cycle started and the garments inside the drum are dry. The code clears when you add wet garments to the drum and start a new cycle. [1] Keep using it? No. Stop using it until the cause is fixed. Start with the owner checks below, beginning with: write down the code and model number.

Source: GE CleanSpeak dryer error-code chart, via Sears PartsDirect [1].

Quick facts

Code	F011
Also shown as	None listed by the manufacturer
Brand / appliance	GE CleanSpeak dryer
System	Heating
Meaning (service chart)	Dry load. The controls detect that a cycle started and the garments inside the drum are dry. The code clears when you add wet garments to the drum and start a new cycle. [1]
Keep using it?	No. Stop using it until the cause is fixed
DIY-safe?	Owner checks only (listed below)
Support	GE Appliances support (products.geappliances.com)
Source document	GE CleanSpeak dryer error-code chart (via Sears PartsDirect)

On this page: Meaning · Steps · Parts · When to call a technician · Related codes · FAQ

What error code F011 means on a GE CleanSpeak dryer

Dry load. The controls detect that a cycle started and the garments inside the drum are dry. The code clears when you add wet garments to the drum and start a new cycle. [1]

This is a heating code. Codes and wording can vary by model, so check your owner's manual for your model number.

How to fix GE CleanSpeak dryer error code F011 (safe owner checks)

Safety first: disconnect power before you remove any panel or reach into the sump or drum. Do not touch wiring, the control board or the motor. If you see water near electrical parts, stop and call a technician. These steps are based on the GE CleanSpeak dryer error-code chart (via Sears PartsDirect) [1], rewritten for clarity.

Write down the code and model number. Note exactly what the display shows (F011) and copy the full model number from the rating label, so you can confirm this chart applies to your cleanSpeak dryer and order the right parts.
Clean the filter. Try our water filter finder Most common symptoms to help you fix your dryers Choose a symptom to see related dryer repairs.
Follow these st. Follow these st...
Check the vent. Clear the exhaust vent duct system of any clogs or restrictions.
Test and decide. Run a short cycle or restart and watch the display. If F011 comes back after these checks, stop using the dryer for this function and call a technician, because the remaining causes need meters or part replacement.

The first and last steps (and the power reset) are general owner checks added by ErrorCodePro; the rest follow the GE CleanSpeak dryer error-code chart published by Sears PartsDirect, rewritten for safe owner use.

Parts that may be involved

Exact parts depend on your model number. This page lists part types only, never part numbers.

No specific part is implied by the manufacturer's guidance for this code.

When to call a technician

Main causes: bad gas valve coils, broken heating element, tripped safety thermostat or fuse, bad operating thermostat, c...
Main causes: clogged exhaust system, heating system failure, deposits on moisture sensor, control system failure...
Main causes: clogged exhaust vent, bad motor relay, loose dryer door catch, bad door switch, control system failure, fau...
Main causes: door switch failure, lack of power, broken belt, blown thermal fuse, bad drive motor, control system failur...
Main causes: lack of electrical power, bad power cord, wiring failure, bad control board, blown thermal fuse, bad door s...
Main causes: bad timer or electronic control board, door switch failure...
Anything involving wiring, the control board, the motor or the water valve electrics
The appliance is under warranty: contact GE Appliances support (products.geappliances.com) first

Frequently asked questions

What does error code F011 mean on a GE CleanSpeak dryer?

The GE CleanSpeak dryer error-code chart lists F011 as follows: Dry load. The controls detect that a cycle started and the garments inside the drum are dry. The code clears when you add wet garments to the drum and start a new cycle.

Is it safe to keep using the CleanSpeak dryer with F011?

No. Stop using it until the cause is fixed.

Can I fix GE CleanSpeak dryer error F011 myself?

Only with the owner checks on this page, starting with: write down the code and model number. If it persists, call a technician or GE Appliances support (products.geappliances.com).

Sources

Sears PartsDirect: GE CleanSpeak dryer error-code chart (third-party copy of manufacturer service data)

Last reviewed: October 20, 2026. ErrorCodePro is not affiliated with GE.