Jenn-Air MicroClean HE dishwasher Error Code F6E4: Meaning & How to Fix It

By the ErrorCodePro Editorial Team · Last reviewed October 20, 2026

Jenn-Air MicroClean HE dishwasher error code F6E4 means: The float switch is open. A defective water inlet valve also can cause the float switch to trip open. A third cause for the error code is a defective float switch. [1] Keep using it? Only if the owner checks below clear the code; if it returns, stop and book a repair. Start with the owner checks below, beginning with: write down the code and model number.

Source: Jenn-Air MicroClean HE dishwasher error-code chart, via Sears PartsDirect [1].

Quick facts

Code	F6E4
Also shown as	6-4
Brand / appliance	Jenn-Air MicroClean HE dishwasher
System	Sensors
Meaning (service chart)	The float switch is open. A defective water inlet valve also can cause the float switch to trip open. A third cause for the error code is a defective float switch. [1]
Keep using it?	Only if the owner checks below clear the code; if it returns, stop and book a repair
DIY-safe?	Owner checks only (listed below)
Support	Jenn-Air customer support (see your owner's manual)
Source document	Jenn-Air MicroClean HE dishwasher error-code chart (via Sears PartsDirect)

On this page: Meaning · Steps · Parts · When to call a technician · Related codes · FAQ

What error code F6E4 means on a Jenn-Air MicroClean HE dishwasher

The float switch is open. A defective water inlet valve also can cause the float switch to trip open. A third cause for the error code is a defective float switch. [1]

This is a sensors code. Codes and wording can vary by model, so check your owner's manual for your model number.

How to fix Jenn-Air MicroClean HE dishwasher error code F6E4 (safe owner checks)

Safety first: disconnect power before you remove any panel or reach into the sump or drum. Do not touch wiring, the control board or the motor. If you see water near electrical parts, stop and call a technician. These steps are based on the Jenn-Air MicroClean HE dishwasher error-code chart (via Sears PartsDirect) [1], rewritten for clarity.

Write down the code and model number. Note exactly what the display shows (F6E4) and copy the full model number from the rating label, so you can confirm this chart applies to your microClean HE dishwasher and order the right parts.
Reduce the load. Check for and remove any items stuck under the overfill float.
Do a power reset. Unplug the appliance or switch off its breaker for one minute, then restore power and try again. If the code clears and stays away, it may have been a one-off fault.
Test and decide. Run a short cycle or restart and watch the display. If F6E4 comes back after these checks, stop using the dishwasher for this function and call a technician, because the remaining causes need meters or part replacement.

The first and last steps (and the power reset) are general owner checks added by ErrorCodePro; the rest follow the Jenn-Air MicroClean HE dishwasher error-code chart published by Sears PartsDirect, rewritten for safe owner use.

Parts that may be involved

Exact parts depend on your model number. This page lists part types only, never part numbers.

Water inlet valve
Overfill float switch

When to call a technician

If this happens, a technician should replace the water inlet valve because the valve is stuck open.
Unplug the dishwasher to disconnect electrical power and check the resistance through the overfill float switch.
You should measure near 0 ohms of resistance with the dishwasher tub empty (or near empty).
If you measure infinite resistance, a technician should replace the float switch.
Anything involving wiring, the control board, the motor or the water valve electrics
The appliance is under warranty: contact Jenn-Air customer support (see your owner's manual) first

Frequently asked questions

What does error code F6E4 mean on a Jenn-Air MicroClean HE dishwasher?

The Jenn-Air MicroClean HE dishwasher error-code chart lists F6E4 as follows: The float switch is open. A defective water inlet valve also can cause the float switch to trip open. A third cause for the error code is a defective float switch.

Is it safe to keep using the MicroClean HE dishwasher with F6E4?

Only if the owner checks below clear the code; if it returns, stop and book a repair.

Can I fix Jenn-Air MicroClean HE dishwasher error F6E4 myself?

Only with the owner checks on this page, starting with: write down the code and model number. If it persists, call a technician or Jenn-Air customer support (see your owner's manual).

Is 6-4 the same as F6E4?

Yes. The source chart lists 6-4 with the same meaning as F6E4; the display format depends on the model.

Sources

Sears PartsDirect: Jenn-Air MicroClean HE dishwasher error-code chart (third-party copy of manufacturer service data)

Last reviewed: October 20, 2026. ErrorCodePro is not affiliated with Jenn-Air.