ErrorCodePro · Appliance Error CodesKenmore 110 model VMAX top-load washer Error Code F5 E2: Meaning & How to Fix It
By the ErrorCodePro Editorial Team · Last reviewed October 20, 2026
Kenmore 110 model VMAX top-load washer error code F5 E2 means: Lid won't lock. [1] Keep using it? Only if the owner checks below clear the code; if it returns, stop and book a repair. Start with the owner checks below, beginning with: write down the code and model number.
Source: Kenmore 110 model VMAX top-load washer error-code chart, via Sears PartsDirect [1].
Quick facts
| Code | F5 E2 |
|---|---|
| Also shown as | None listed by the manufacturer |
| Brand / appliance | Kenmore 110 model VMAX top-load washer |
| System | Door / lock |
| Meaning (service chart) | Lid won't lock. [1] |
| Keep using it? | Only if the owner checks below clear the code; if it returns, stop and book a repair |
| DIY-safe? | Owner checks only (listed below) |
| Support | Kenmore customer support (kenmore.com) or a Sears-authorized technician |
| Source document | Kenmore 110 model VMAX top-load washer error-code chart (via Sears PartsDirect) |
On this page: Meaning · Steps · Parts · When to call a technician · Related codes · FAQ
What error code F5 E2 means on a Kenmore 110 model VMAX top-load washer
Lid won't lock. [1]
This is a door / lock code. Codes and wording can vary by model, so check your owner's manual for your model number.
How to fix Kenmore 110 model VMAX top-load washer error code F5 E2 (safe owner checks)
- Write down the code and model number. Note exactly what the display shows (F5 E2) and copy the full model number from the rating label, so you can confirm this chart applies to your 110 model VMAX top-load washer and order the right parts.
- Close the door or lid fully. Check for debris in the lid lock mechanism that could prevent it from locking.
- Do a power reset. Unplug the appliance or switch off its breaker for one minute, then restore power and try again. If the code clears and stays away, it may have been a one-off fault.
- Test and decide. Run a short cycle or restart and watch the display. If F5 E2 comes back after these checks, stop using the washer for this function and call a technician, because the remaining causes need meters or part replacement.
The first and last steps (and the power reset) are general owner checks added by ErrorCodePro; the rest follow the Kenmore 110 model VMAX top-load washer error-code chart published by Sears PartsDirect, rewritten for safe owner use.
Parts that may be involved
Exact parts depend on your model number. This page lists part types only, never part numbers.
- Lid lock/switch
When to call a technician
- Unplug the washer and check the wire harness connections for the lid lock/switch on the main electronic control board.
- If it's damaged or defective, a technician should replace it.
- Anything involving wiring, the control board, the motor or the water valve electrics
- The appliance is under warranty: contact Kenmore customer support (kenmore.com) or a Sears-authorized technician first
Related error codes
Frequently asked questions
What does error code F5 E2 mean on a Kenmore 110 model VMAX top-load washer?
The Kenmore 110 model VMAX top-load washer error-code chart lists F5 E2 as follows: Lid won't lock.
Is it safe to keep using the 110 model VMAX top-load washer with F5 E2?
Only if the owner checks below clear the code; if it returns, stop and book a repair.
Can I fix Kenmore 110 model VMAX top-load washer error F5 E2 myself?
Only with the owner checks on this page, starting with: write down the code and model number. If it persists, call a technician or Kenmore customer support (kenmore.com) or a Sears-authorized technician.
Sources
- Sears PartsDirect: Kenmore 110 model VMAX top-load washer error-code chart (third-party copy of manufacturer service data)
Last reviewed: October 20, 2026. ErrorCodePro is not affiliated with Kenmore.