ErrorCodePro · Appliance Error CodesKenmore 110 model VMW top-load washer Error Code F9 E1: Meaning & How to Fix It
By the ErrorCodePro Editorial Team · Last reviewed October 20, 2026
Kenmore 110 model VMW top-load washer error code F9 E1 means: Long drain time. The washer isn't draining after the drain pump runs for 10 minutes. [1] Keep using it? Only if the owner checks below clear the code; if it returns, stop and book a repair. Start with the owner checks below, beginning with: write down the code and model number.
Source: Kenmore 110 model VMW top-load washer error-code chart, via Sears PartsDirect [1].
Quick facts
| Code | F9 E1 |
|---|---|
| Also shown as | None listed by the manufacturer |
| Brand / appliance | Kenmore 110 model VMW top-load washer |
| System | Drain |
| Meaning (service chart) | Long drain time. The washer isn't draining after the drain pump runs for 10 minutes. [1] |
| Keep using it? | Only if the owner checks below clear the code; if it returns, stop and book a repair |
| DIY-safe? | Owner checks only (listed below) |
| Support | Kenmore customer support (kenmore.com) or a Sears-authorized technician |
| Source document | Kenmore 110 model VMW top-load washer error-code chart (via Sears PartsDirect) |
On this page: Meaning · Steps · Parts · When to call a technician · Related codes · FAQ
What error code F9 E1 means on a Kenmore 110 model VMW top-load washer
Long drain time. The washer isn't draining after the drain pump runs for 10 minutes. [1]
This is a drain code. Codes and wording can vary by model, so check your owner's manual for your model number.
How to fix Kenmore 110 model VMW top-load washer error code F9 E1 (safe owner checks)
- Write down the code and model number. Note exactly what the display shows (F9 E1) and copy the full model number from the rating label, so you can confirm this chart applies to your 110 model VMW top-load washer and order the right parts.
- Check the drain hose. Check the washer drain and the drain hose for clogs or restrictions.
- Do a power reset. Unplug the appliance or switch off its breaker for one minute, then restore power and try again. If the code clears and stays away, it may have been a one-off fault.
- Test and decide. Run a short cycle or restart and watch the display. If F9 E1 comes back after these checks, stop using the washer for this function and call a technician, because the remaining causes need meters or part replacement.
The first and last steps (and the power reset) are general owner checks added by ErrorCodePro; the rest follow the Kenmore 110 model VMW top-load washer error-code chart published by Sears PartsDirect, rewritten for safe owner use.
Parts that may be involved
Exact parts depend on your model number. This page lists part types only, never part numbers.
- Drain pump
When to call a technician
- If the drain pump is defective, a technician should replace it.
- Anything involving wiring, the control board, the motor or the water valve electrics
- The appliance is under warranty: contact Kenmore customer support (kenmore.com) or a Sears-authorized technician first
Related error codes
Frequently asked questions
What does error code F9 E1 mean on a Kenmore 110 model VMW top-load washer?
The Kenmore 110 model VMW top-load washer error-code chart lists F9 E1 as follows: Long drain time. The washer isn't draining after the drain pump runs for 10 minutes.
Is it safe to keep using the 110 model VMW top-load washer with F9 E1?
Only if the owner checks below clear the code; if it returns, stop and book a repair.
Can I fix Kenmore 110 model VMW top-load washer error F9 E1 myself?
Only with the owner checks on this page, starting with: write down the code and model number. If it persists, call a technician or Kenmore customer support (kenmore.com) or a Sears-authorized technician.
Sources
- Sears PartsDirect: Kenmore 110 model VMW top-load washer error-code chart (third-party copy of manufacturer service data)
Last reviewed: October 20, 2026. ErrorCodePro is not affiliated with Kenmore.