ErrorCodePro · Appliance Error CodesKenmore Calypso top-load washer Error Code Er: Meaning & How to Fix It
By the ErrorCodePro Editorial Team · Last reviewed October 20, 2026
Kenmore Calypso top-load washer error code Er means: Control board error. The electronic control board failed to save cycle information during a power failure. [1] Keep using it? Only if the owner checks below clear the code; if it returns, stop and book a repair. Start with the owner checks below, beginning with: write down the code and model number.
Source: Kenmore Calypso top-load washer error-code chart, via Sears PartsDirect [1].
Quick facts
| Code | Er |
|---|---|
| Also shown as | None listed by the manufacturer |
| Brand / appliance | Kenmore Calypso top-load washer |
| System | Control / electronics |
| Meaning (service chart) | Control board error. The electronic control board failed to save cycle information during a power failure. [1] |
| Keep using it? | Only if the owner checks below clear the code; if it returns, stop and book a repair |
| DIY-safe? | Owner checks only (listed below) |
| Support | Kenmore customer support (kenmore.com) or a Sears-authorized technician |
| Source document | Kenmore Calypso top-load washer error-code chart (via Sears PartsDirect) |
On this page: Meaning · Steps · Parts · When to call a technician · Related codes · FAQ
What error code Er means on a Kenmore Calypso top-load washer
Control board error. The electronic control board failed to save cycle information during a power failure. [1]
This is a control / electronics code. Codes and wording can vary by model, so check your owner's manual for your model number.
How to fix Kenmore Calypso top-load washer error code Er (safe owner checks)
- Write down the code and model number. Note exactly what the display shows (Er) and copy the full model number from the rating label, so you can confirm this chart applies to your calypso top-load washer and order the right parts.
- Rebalance the load. Press Stop/Cancel to clear the display and set a new cycle to finish the load.
- Do a power reset. Unplug the appliance or switch off its breaker for one minute, then restore power and try again. If the code clears and stays away, it may have been a one-off fault.
- Test and decide. Run a short cycle or restart and watch the display. If Er comes back after these checks, stop using the washer for this function and call a technician, because the remaining causes need meters or part replacement.
The first and last steps (and the power reset) are general owner checks added by ErrorCodePro; the rest follow the Kenmore Calypso top-load washer error-code chart published by Sears PartsDirect, rewritten for safe owner use.
Parts that may be involved
Exact parts depend on your model number. This page lists part types only, never part numbers.
No specific part is implied by the manufacturer's guidance for this code.
When to call a technician
- Anything involving wiring, the control board, the motor or the water valve electrics
- The appliance is under warranty: contact Kenmore customer support (kenmore.com) or a Sears-authorized technician first
Related error codes
Frequently asked questions
What does error code Er mean on a Kenmore Calypso top-load washer?
The Kenmore Calypso top-load washer error-code chart lists Er as follows: Control board error. The electronic control board failed to save cycle information during a power failure.
Is it safe to keep using the Calypso top-load washer with Er?
Only if the owner checks below clear the code; if it returns, stop and book a repair.
Can I fix Kenmore Calypso top-load washer error Er myself?
Only with the owner checks on this page, starting with: write down the code and model number. If it persists, call a technician or Kenmore customer support (kenmore.com) or a Sears-authorized technician.
Sources
- Sears PartsDirect: Kenmore Calypso top-load washer error-code chart (third-party copy of manufacturer service data)
Last reviewed: October 20, 2026. ErrorCodePro is not affiliated with Kenmore.