ErrorCodePro · Appliance Error CodesKitchenAid Induction cooktop Error Code F2: Meaning & How to Fix It
By the ErrorCodePro Editorial Team · Last reviewed October 20, 2026
KitchenAid induction cooktop error code F2 means: The surface cooking area is too hot and has turned off. The F2 code disappears when the surface cooking area cools. [1] Keep using it? No. Stop using it until the cause is fixed. Start with the owner checks below, beginning with: write down the code and model number.
Source: KitchenAid induction cooktop error-code chart, via Sears PartsDirect [1].
Quick facts
| Code | F2 |
|---|---|
| Also shown as | None listed by the manufacturer |
| Brand / appliance | KitchenAid induction cooktop |
| System | Heating |
| Meaning (service chart) | The surface cooking area is too hot and has turned off. The F2 code disappears when the surface cooking area cools. [1] |
| Keep using it? | No. Stop using it until the cause is fixed |
| DIY-safe? | Owner checks only (listed below) |
| Support | KitchenAid Product Help (producthelp.kitchenaid.com) |
| Source document | KitchenAid induction cooktop error-code chart (via Sears PartsDirect) |
On this page: Meaning · Steps · Parts · When to call a technician · Related codes · FAQ
What error code F2 means on a KitchenAid induction cooktop
The surface cooking area is too hot and has turned off. The F2 code disappears when the surface cooking area cools. [1]
This is a heating code. Codes and wording can vary by model, so check your owner's manual for your model number.
How to fix KitchenAid induction cooktop error code F2 (safe owner checks)
- Write down the code and model number. Note exactly what the display shows (F2) and copy the full model number from the rating label, so you can confirm this chart applies to your induction cooktop and order the right parts.
- Remove the pans from the. Remove the pans from the surface cooking area.
- Do a power reset. Unplug the appliance or switch off its breaker for one minute, then restore power and try again. If the code clears and stays away, it may have been a one-off fault.
- Test and decide. Run a short cycle or restart and watch the display. If F2 comes back after these checks, stop using the range for this function and call a technician, because the remaining causes need meters or part replacement.
The first and last steps (and the power reset) are general owner checks added by ErrorCodePro; the rest follow the KitchenAid induction cooktop error-code chart published by Sears PartsDirect, rewritten for safe owner use.
Parts that may be involved
Exact parts depend on your model number. This page lists part types only, never part numbers.
- Sensor
- Electronic control board
When to call a technician
- If the F2 code reappears when you turn the cooktop on, a sensor or internal control board is defective.
- Call a service technician to diagnose and repair the cooktop.
- Anything involving wiring, the control board, the motor or the water valve electrics
- The appliance is under warranty: contact KitchenAid Product Help (producthelp.kitchenaid.com) first
Related error codes
Frequently asked questions
What does error code F2 mean on a KitchenAid induction cooktop?
The KitchenAid induction cooktop error-code chart lists F2 as follows: The surface cooking area is too hot and has turned off. The F2 code disappears when the surface cooking area cools.
Is it safe to keep using the induction cooktop with F2?
No. Stop using it until the cause is fixed.
Can I fix KitchenAid induction cooktop error F2 myself?
Only with the owner checks on this page, starting with: write down the code and model number. If it persists, call a technician or KitchenAid Product Help (producthelp.kitchenaid.com).
Sources
- Sears PartsDirect: KitchenAid induction cooktop error-code chart (third-party copy of manufacturer service data)
Last reviewed: October 20, 2026. ErrorCodePro is not affiliated with KitchenAid.