ErrorCodePro · Appliance Error CodesLG Dryer Error Codes: Full List & Meanings
Every LG dryer error code we have verified against LG's own support pages, with its official meaning. Codes vary by model, so confirm in your owner's manual. Support: LG USA Support (lg.com/us/support).
Codes by system
Venting / airflow
Door / lock
Sensors
Power supply
Drain
Water fill
All LG dryer error codes
Codes marked "Reset only" or "Service" have no separate page because the manufacturer publishes no owner fix beyond a reset or a service call.
| Code | Official meaning | System | Owner action |
|---|---|---|---|
| d80 | Airflow is restricted between the dryer and the outside exhaust. d90 and d95 mean progressively worse restriction. Also: d90, d95 | Venting / airflow | Owner checks |
| dE | The door isn't completely closed. Also: dE4 | Door / lock | Owner checks |
| tE2 | A thermistor problem, usually in cold conditions. It can happen during steam cycles if the duct cools too quickly. | Sensors | Owner checks |
| nP | No current is detected at the heater. This usually points to home wiring. | Power supply | Owner checks |
| HS | A humidity sensor error. The dryer may run for 2½ hours. | Sensors | Owner checks |
| FO | The lint filter isn't inserted properly (FO or a flashing INSERT FILTER). Also: INSERT FILTER, IF | Sensors | Owner checks |
| E13 | On hybrid condensing dryers, the drain hose is kinked, crushed or clogged, or the sump water is frozen. | Drain | Owner checks |
| drn | Water can't drain: the container is full, the drain hose is kinked or too high, or there's air in the drain pump. Also: OE | Drain | Owner checks |
| Add Water | The steam feeder needs water. | Water fill | Owner checks |
| E05 | There's a problem with the water supply for the steam cycle. Also: E5 | Water fill | Owner checks |
| tE1 | LG lists tE1 as: thermistor; unplug, hold START/PAUSE 5 s, restore power. Unplug for 60 seconds and restart. If it persists, request service. Also: tE3, tE4, tE5, tE6 | Control / electronics | Service |
| PS | LG lists PS as: improper cord voltage (cord wiring); have the installer or an electrician check the terminal block. Unplug for 60 seconds and restart. If it persists, request service. | Control / electronics | Service |
| gAS | LG lists gAS as: no gas reaching dryer; check the valve is on, and a pro handles gas-line issues. Unplug for 60 seconds and restart. If it persists, request service. | Control / electronics | Service |
| LE1 | LG lists LE1 as: drum motor (reduce the load, then service). Unplug for 60 seconds and restart. If it persists, request service. | Control / electronics | Service |
| LE2 | LG lists LE2 as: compressor (heat pump). Unplug for 60 seconds and restart. If it persists, request service. Also: AE, CE1 | Control / electronics | Service |
| LE3 | LG lists LE3 as: air circulation motor. Unplug for 60 seconds and restart. If it persists, request service. | Control / electronics | Service |
| E1 | LG lists E1 as: steam generator (steam models). Unplug for 60 seconds and restart. If it persists, request service. Also: E4 | Control / electronics | Service |
| nE | LG lists nE as: Wi-Fi/NFC module communication. Unplug for 60 seconds and restart. If it persists, request service. Also: nF, nC | Control / electronics | Service |
| bE | LG lists bE as: drum drive belt. Unplug for 60 seconds and restart. If it persists, request service. | Control / electronics | Service |
| E00 | LG lists E00 as: display can't read main board software. Unplug for 60 seconds and restart. If it persists, request service. | Control / electronics | Service |
| E03 | LG lists E03 as: drain tank; empty it, then reset. Unplug for 60 seconds and restart. If it persists, request service. | Control / electronics | Service |
| EHE | LG lists EHE as: heater over-current. Unplug for 60 seconds and restart. If it persists, request service. | Control / electronics | Service |
| F1 | LG lists F1 as: unplug 60 seconds, then service. Unplug for 60 seconds and restart. If it persists, request service. | Control / electronics | Service |
| PF | LG lists PF as: power failure; unplug, hold START/PAUSE 5 s. Unplug for 60 seconds and restart. If it persists, request service. | Control / electronics | Service |
| CL | LG lists CL as: child lock on; hold Child Lock 3–5 s. Unplug for 60 seconds and restart. If it persists, request service. | Control / electronics | Service |
Symptoms
Sources
Last reviewed: October 20, 2026. ErrorCodePro is not affiliated with LG.