Electrolux IQ-Touch dryer Error Code E92: Meaning & How to Fix It

By the ErrorCodePro Editorial Team · Last reviewed October 20, 2026

Electrolux IQ-Touch dryer error code E92 means: User interface control and electronic control board mismatch. [1] Keep using it? Only if the owner checks below clear the code; if it returns, stop and book a repair. Start with the owner checks below, beginning with: write down the code and model number.

Source: Electrolux IQ-Touch dryer error-code chart, via Sears PartsDirect [1].

Quick facts

Code	E92
Also shown as	None listed by the manufacturer
Brand / appliance	Electrolux IQ-Touch dryer
System	Control / electronics
Meaning (service chart)	User interface control and electronic control board mismatch. [1]
Keep using it?	Only if the owner checks below clear the code; if it returns, stop and book a repair
DIY-safe?	Owner checks only (listed below)
Support	Electrolux support (owner.electrolux.com)
Source document	Electrolux IQ-Touch dryer error-code chart (via Sears PartsDirect)

On this page: Meaning · Steps · Parts · When to call a technician · Related codes · FAQ

What error code E92 means on an Electrolux IQ-Touch dryer

User interface control and electronic control board mismatch. [1]

This is a control / electronics code. Codes and wording can vary by model, so check your owner's manual for your model number.

How to fix Electrolux IQ-Touch dryer error code E92 (safe owner checks)

Safety first: disconnect power before you remove any panel or reach into the sump or drum. Do not touch wiring, the control board or the motor. If you see water near electrical parts, stop and call a technician. These steps are based on the Electrolux IQ-Touch dryer error-code chart (via Sears PartsDirect) [1], rewritten for clarity.

Write down the code and model number. Note exactly what the display shows (E92) and copy the full model number from the rating label, so you can confirm this chart applies to your IQ-Touch dryer and order the right parts.
Use your dryer model number. Use your dryer model number to check the part number for the replacement part.
Do a power reset. Unplug the dryer and install the correct part for your model.
Test and decide. Run a short cycle or restart and watch the display. If E92 comes back after these checks, stop using the dryer for this function and call a technician, because the remaining causes need meters or part replacement.

The first and last steps (and the power reset) are general owner checks added by ErrorCodePro; the rest follow the Electrolux IQ-Touch dryer error-code chart published by Sears PartsDirect, rewritten for safe owner use.

Parts that may be involved

Exact parts depend on your model number. This page lists part types only, never part numbers.

User interface control
Electronic control board

When to call a technician

This code appears when you replace the user interface control or electronic control board using the wrong part.
Anything involving wiring, the control board, the motor or the water valve electrics
The appliance is under warranty: contact Electrolux support (owner.electrolux.com) first

Frequently asked questions

What does error code E92 mean on an Electrolux IQ-Touch dryer?

The Electrolux IQ-Touch dryer error-code chart lists E92 as follows: User interface control and electronic control board mismatch.

Is it safe to keep using the IQ-Touch dryer with E92?

Only if the owner checks below clear the code; if it returns, stop and book a repair.

Can I fix Electrolux IQ-Touch dryer error E92 myself?

Only with the owner checks on this page, starting with: write down the code and model number. If it persists, call a technician or Electrolux support (owner.electrolux.com).

Sources

Sears PartsDirect: Electrolux IQ-Touch dryer error-code chart (third-party copy of manufacturer service data)

Last reviewed: October 20, 2026. ErrorCodePro is not affiliated with Electrolux.