ErrorCodePro · Appliance Error CodesElectrolux IQ-Touch dryer Error Code E93: Meaning & How to Fix It
By the ErrorCodePro Editorial Team · Last reviewed October 20, 2026
Electrolux IQ-Touch dryer error code E93 means: Machine configuration error. [1] Keep using it? Only if the owner checks below clear the code; if it returns, stop and book a repair. Start with the owner checks below, beginning with: write down the code and model number.
Source: Electrolux IQ-Touch dryer error-code chart, via Sears PartsDirect [1].
Quick facts
| Code | E93 |
|---|---|
| Also shown as | None listed by the manufacturer |
| Brand / appliance | Electrolux IQ-Touch dryer |
| System | Control / electronics |
| Meaning (service chart) | Machine configuration error. [1] |
| Keep using it? | Only if the owner checks below clear the code; if it returns, stop and book a repair |
| DIY-safe? | Owner checks only (listed below) |
| Support | Electrolux support (owner.electrolux.com) |
| Source document | Electrolux IQ-Touch dryer error-code chart (via Sears PartsDirect) |
On this page: Meaning · Steps · Parts · When to call a technician · Related codes · FAQ
What error code E93 means on an Electrolux IQ-Touch dryer
Machine configuration error. [1]
This is a control / electronics code. Codes and wording can vary by model, so check your owner's manual for your model number.
How to fix Electrolux IQ-Touch dryer error code E93 (safe owner checks)
- Write down the code and model number. Note exactly what the display shows (E93) and copy the full model number from the rating label, so you can confirm this chart applies to your IQ-Touch dryer and order the right parts.
- Use your dryer model number. Use your dryer model number to check the part number for the replacement part.
- Install the correct part. Install the correct part for your model.
- Do a power reset. Unplug the appliance or switch off its breaker for one minute, then restore power and try again. If the code clears and stays away, it may have been a one-off fault.
- Test and decide. Run a short cycle or restart and watch the display. If E93 comes back after these checks, stop using the dryer for this function and call a technician, because the remaining causes need meters or part replacement.
The first and last steps (and the power reset) are general owner checks added by ErrorCodePro; the rest follow the Electrolux IQ-Touch dryer error-code chart published by Sears PartsDirect, rewritten for safe owner use.
Parts that may be involved
Exact parts depend on your model number. This page lists part types only, never part numbers.
- User interface control
- Electronic control board
- Wire harness
When to call a technician
- Unplug the dryer and check the wire harness connections between the user interface control and the electronic control board.
- Reconnect any loose wires or replace the wire harness if damaged.
- If the wiring is okay and you just replaced the user interface control or electronic control board, then you could have used the wrong part.
- Anything involving wiring, the control board, the motor or the water valve electrics
- The appliance is under warranty: contact Electrolux support (owner.electrolux.com) first
Related error codes
Frequently asked questions
What does error code E93 mean on an Electrolux IQ-Touch dryer?
The Electrolux IQ-Touch dryer error-code chart lists E93 as follows: Machine configuration error.
Is it safe to keep using the IQ-Touch dryer with E93?
Only if the owner checks below clear the code; if it returns, stop and book a repair.
Can I fix Electrolux IQ-Touch dryer error E93 myself?
Only with the owner checks on this page, starting with: write down the code and model number. If it persists, call a technician or Electrolux support (owner.electrolux.com).
Sources
- Sears PartsDirect: Electrolux IQ-Touch dryer error-code chart (third-party copy of manufacturer service data)
Last reviewed: October 20, 2026. ErrorCodePro is not affiliated with Electrolux.