GE CleanSpeak top-load washer Error Code 0A: Meaning & How to Fix It

By the ErrorCodePro Editorial Team · Last reviewed October 20, 2026

GE CleanSpeak top-load washer error code 0A means: Not filling with water. [1] Keep using it? Only if the owner checks below clear the code; if it returns, stop and book a repair. Start with the owner checks below, beginning with: write down the code and model number.

Source: GE CleanSpeak top-load washer error-code chart, via Sears PartsDirect [1].

Quick facts

Code	0A
Also shown as	10
Brand / appliance	GE CleanSpeak top-load washer
System	Water fill
Meaning (service chart)	Not filling with water. [1]
Keep using it?	Only if the owner checks below clear the code; if it returns, stop and book a repair
DIY-safe?	Owner checks only (listed below)
Support	GE Appliances support (products.geappliances.com)
Source document	GE CleanSpeak top-load washer error-code chart (via Sears PartsDirect)

On this page: Meaning · Steps · Parts · When to call a technician · Related codes · FAQ

What error code 0A means on a GE CleanSpeak top-load washer

Not filling with water. [1]

This is a water fill code. Codes and wording can vary by model, so check your owner's manual for your model number.

How to fix GE CleanSpeak top-load washer error code 0A (safe owner checks)

Safety first: disconnect power before you remove any panel or reach into the sump or drum. Do not touch wiring, the control board or the motor. If you see water near electrical parts, stop and call a technician. These steps are based on the GE CleanSpeak top-load washer error-code chart (via Sears PartsDirect) [1], rewritten for clarity.

Write down the code and model number. Note exactly what the display shows (0A) and copy the full model number from the rating label, so you can confirm this chart applies to your cleanSpeak top-load washer and order the right parts.
Open the water supply. Make sure that both water supply valves behind the washer are fully open.
Check the drain system. Check the drain system for a siphon problem.
Do a power reset. Unplug the appliance or switch off its breaker for one minute, then restore power and try again. If the code clears and stays away, it may have been a one-off fault.
Test and decide. Run a short cycle or restart and watch the display. If 0A comes back after these checks, stop using the washer for this function and call a technician, because the remaining causes need meters or part replacement.

The first and last steps (and the power reset) are general owner checks added by ErrorCodePro; the rest follow the GE CleanSpeak top-load washer error-code chart published by Sears PartsDirect, rewritten for safe owner use.

Parts that may be involved

Exact parts depend on your model number. This page lists part types only, never part numbers.

Water inlet valve assembly

When to call a technician

If the water inlet valve assembly is defective, a technician should replace it.
Anything involving wiring, the control board, the motor or the water valve electrics
The appliance is under warranty: contact GE Appliances support (products.geappliances.com) first

Frequently asked questions

What does error code 0A mean on a GE CleanSpeak top-load washer?

The GE CleanSpeak top-load washer error-code chart lists 0A as follows: Not filling with water.

Is it safe to keep using the CleanSpeak top-load washer with 0A?

Only if the owner checks below clear the code; if it returns, stop and book a repair.

Can I fix GE CleanSpeak top-load washer error 0A myself?

Only with the owner checks on this page, starting with: write down the code and model number. If it persists, call a technician or GE Appliances support (products.geappliances.com).

Is 10 the same as 0A?

Yes. The source chart lists 10 with the same meaning as 0A; the display format depends on the model.

Sources

Sears PartsDirect: GE CleanSpeak top-load washer error-code chart (third-party copy of manufacturer service data)

Last reviewed: October 20, 2026. ErrorCodePro is not affiliated with GE.