GE GFW front-load washer Error Code 25: Meaning & How to Fix It

By the ErrorCodePro Editorial Team · Last reviewed October 20, 2026

GE GFW front-load washer error code 25 means: Control detects water level drop when the washer isn’t draining. An improperly installed drain hose can allow water to siphon out of the washer during the cycle. [1] Keep using it? Only if the owner checks below clear the code; if it returns, stop and book a repair. Start with the owner checks below, beginning with: write down the code and model number.

Source: GE GFW front-load washer error-code chart, via Sears PartsDirect [1].

Quick facts

Code	25
Also shown as	65
Brand / appliance	GE GFW front-load washer
System	Drain
Meaning (service chart)	Control detects water level drop when the washer isn’t draining. An improperly installed drain hose can allow water to siphon out of the washer during the cycle. [1]
Keep using it?	Only if the owner checks below clear the code; if it returns, stop and book a repair
DIY-safe?	Owner checks only (listed below)
Support	GE Appliances support (products.geappliances.com)
Source document	GE GFW front-load washer error-code chart (via Sears PartsDirect)

On this page: Meaning · Steps · Parts · When to call a technician · Related codes · FAQ

What error code 25 means on a GE GFW front-load washer

Control detects water level drop when the washer isn’t draining. An improperly installed drain hose can allow water to siphon out of the washer during the cycle. [1]

This is a drain code. Codes and wording can vary by model, so check your owner's manual for your model number.

How to fix GE GFW front-load washer error code 25 (safe owner checks)

Safety first: disconnect power before you remove any panel or reach into the sump or drum. Do not touch wiring, the control board or the motor. If you see water near electrical parts, stop and call a technician. These steps are based on the GE GFW front-load washer error-code chart (via Sears PartsDirect) [1], rewritten for clarity.

Write down the code and model number. Note exactly what the display shows (25) and copy the full model number from the rating label, so you can confirm this chart applies to your GFW front-load washer and order the right parts.
Check the drain hose. Check the drain hose for proper installation. Follow the washer installation instructions to correctly install the drain hose if it isn’t installed properly.
Reconnect the air hose. Reconnect the air hose if it’s loose.
Check. Check for leaks from the washer tub.
Do a power reset. Unplug the appliance or switch off its breaker for one minute, then restore power and try again. If the code clears and stays away, it may have been a one-off fault.
Test and decide. Run a short cycle or restart and watch the display. If 25 comes back after these checks, stop using the washer for this function and call a technician, because the remaining causes need meters or part replacement.

The first and last steps (and the power reset) are general owner checks added by ErrorCodePro; the rest follow the GE GFW front-load washer error-code chart published by Sears PartsDirect, rewritten for safe owner use.

Parts that may be involved

Exact parts depend on your model number. This page lists part types only, never part numbers.

Water level pressure switch air hose
Washer tub

When to call a technician

Unplug the washer and check the air hose between the bottom of the tub and the connection on the electronic control board.
Technician: replace the air hose if it’s pinched, punctured or damaged.
Technician: replace the tub if it’s damaged.
Anything involving wiring, the control board, the motor or the water valve electrics
The appliance is under warranty: contact GE Appliances support (products.geappliances.com) first

Frequently asked questions

What does error code 25 mean on a GE GFW front-load washer?

The GE GFW front-load washer error-code chart lists 25 as follows: Control detects water level drop when the washer isn’t draining. An improperly installed drain hose can allow water to siphon out of the washer during the cycle.

Is it safe to keep using the GFW front-load washer with 25?

Only if the owner checks below clear the code; if it returns, stop and book a repair.

Can I fix GE GFW front-load washer error 25 myself?

Only with the owner checks on this page, starting with: write down the code and model number. If it persists, call a technician or GE Appliances support (products.geappliances.com).

Is 65 the same as 25?

Yes. The source chart lists 65 with the same meaning as 25; the display format depends on the model.

Sources

Sears PartsDirect: GE GFW front-load washer error-code chart (third-party copy of manufacturer service data)

Last reviewed: October 20, 2026. ErrorCodePro is not affiliated with GE.