GE GFW front-load washer Error Code 29: Meaning & How to Fix It

By the ErrorCodePro Editorial Team · Last reviewed October 20, 2026

GE GFW front-load washer error code 29 means: Excessive suds caused the cycle to stop. [1] Keep using it? Only if the owner checks below clear the code; if it returns, stop and book a repair. Start with the owner checks below, beginning with: write down the code and model number.

Source: GE GFW front-load washer error-code chart, via Sears PartsDirect [1].

Quick facts

Code	29
Also shown as	None listed by the manufacturer
Brand / appliance	GE GFW front-load washer
System	Suds / detergent
Meaning (service chart)	Excessive suds caused the cycle to stop. [1]
Keep using it?	Only if the owner checks below clear the code; if it returns, stop and book a repair
DIY-safe?	Owner checks only (listed below)
Support	GE Appliances support (products.geappliances.com)
Source document	GE GFW front-load washer error-code chart (via Sears PartsDirect)

On this page: Meaning · Steps · Parts · When to call a technician · Related codes · FAQ

What error code 29 means on a GE GFW front-load washer

Excessive suds caused the cycle to stop. [1]

This is a suds / detergent code. Codes and wording can vary by model, so check your owner's manual for your model number.

How to fix GE GFW front-load washer error code 29 (safe owner checks)

Safety first: disconnect power before you remove any panel or reach into the sump or drum. Do not touch wiring, the control board or the motor. If you see water near electrical parts, stop and call a technician. These steps are based on the GE GFW front-load washer error-code chart (via Sears PartsDirect) [1], rewritten for clarity.

Write down the code and model number. Note exactly what the display shows (29) and copy the full model number from the rating label, so you can confirm this chart applies to your GFW front-load washer and order the right parts.
Fix the detergent dose. Let the suds dissipate, then finish running the rinse, drain and spin cycle. Use the right amount of HE (high efficiency) detergent to avoid excessive suds during the cycle.
Do a power reset. Unplug the appliance or switch off its breaker for one minute, then restore power and try again. If the code clears and stays away, it may have been a one-off fault.
Test and decide. Run a short cycle or restart and watch the display. If 29 comes back after these checks, stop using the washer for this function and call a technician, because the remaining causes need meters or part replacement.

The first and last steps (and the power reset) are general owner checks added by ErrorCodePro; the rest follow the GE GFW front-load washer error-code chart published by Sears PartsDirect, rewritten for safe owner use.

Parts that may be involved

Exact parts depend on your model number. This page lists part types only, never part numbers.

HE detergent

When to call a technician

Anything involving wiring, the control board, the motor or the water valve electrics
The appliance is under warranty: contact GE Appliances support (products.geappliances.com) first

Frequently asked questions

What does error code 29 mean on a GE GFW front-load washer?

The GE GFW front-load washer error-code chart lists 29 as follows: Excessive suds caused the cycle to stop.

Is it safe to keep using the GFW front-load washer with 29?

Only if the owner checks below clear the code; if it returns, stop and book a repair.

Can I fix GE GFW front-load washer error 29 myself?

Only with the owner checks on this page, starting with: write down the code and model number. If it persists, call a technician or GE Appliances support (products.geappliances.com).

Sources

Sears PartsDirect: GE GFW front-load washer error-code chart (third-party copy of manufacturer service data)

Last reviewed: October 20, 2026. ErrorCodePro is not affiliated with GE.