GE Wall oven Error Code F0, F1: Meaning & How to Fix It

By the ErrorCodePro Editorial Team · Last reviewed October 20, 2026

GE wall oven error code F0, F1 means: Stuck or defective button on the key panel. [1] Keep using it? Only if the owner checks below clear the code; if it returns, stop and book a repair. Start with the owner checks below, beginning with: write down the code and model number.

Source: GE wall oven error-code chart, via Sears PartsDirect [1].

Quick facts

Code	F0, F1
Also shown as	F7
Brand / appliance	GE wall oven
System	Control / electronics
Meaning (service chart)	Stuck or defective button on the key panel. [1]
Keep using it?	Only if the owner checks below clear the code; if it returns, stop and book a repair
DIY-safe?	Owner checks only (listed below)
Support	GE Appliances support (products.geappliances.com)
Source document	GE wall oven error-code chart (via Sears PartsDirect)

On this page: Meaning · Steps · Parts · When to call a technician · Related codes · FAQ

What error code F0, F1 means on a GE wall oven

Stuck or defective button on the key panel. [1]

This is a control / electronics code. Codes and wording can vary by model, so check your owner's manual for your model number.

How to fix GE wall oven error code F0, F1 (safe owner checks)

Safety first: disconnect power before you remove any panel or reach into the sump or drum. Do not touch wiring, the control board or the motor. If you see water near electrical parts, stop and call a technician. These steps are based on the GE wall oven error-code chart (via Sears PartsDirect) [1], rewritten for clarity.

Write down the code and model number. Note exactly what the display shows (F0, F1) and copy the full model number from the rating label, so you can confirm this chart applies to your wall oven and order the right parts.
Clear any clog or debris. Push the Clear/OFF pad.
Do a power reset. Unplug the appliance or switch off its breaker for one minute, then restore power and try again. If the code clears and stays away, it may have been a one-off fault.
Test and decide. Run a short cycle or restart and watch the display. If F0, F1 comes back after these checks, stop using the range for this function and call a technician, because the remaining causes need meters or part replacement.

The first and last steps (and the power reset) are general owner checks added by ErrorCodePro; the rest follow the GE wall oven error-code chart published by Sears PartsDirect, rewritten for safe owner use.

Parts that may be involved

Exact parts depend on your model number. This page lists part types only, never part numbers.

Key panel
Electronic oven control board

When to call a technician

Shut off power to the oven, disconnect the flat ribbon connector from the electronic oven control board and then restore electrical power.
If the code reappears after about 30 seconds, a technician should replace the electronic oven control board.
If the code doesn't reappear, a technician should replace the key panel.
Anything involving wiring, the control board, the motor or the water valve electrics
The appliance is under warranty: contact GE Appliances support (products.geappliances.com) first

Frequently asked questions

What does error code F0, F1 mean on a GE wall oven?

The GE wall oven error-code chart lists F0, F1 as follows: Stuck or defective button on the key panel.

Is it safe to keep using the wall oven with F0, F1?

Only if the owner checks below clear the code; if it returns, stop and book a repair.

Can I fix GE wall oven error F0, F1 myself?

Only with the owner checks on this page, starting with: write down the code and model number. If it persists, call a technician or GE Appliances support (products.geappliances.com).

Is F7 the same as F0, F1?

Yes. The source chart lists F7 with the same meaning as F0, F1; the display format depends on the model.

Sources

Sears PartsDirect: GE wall oven error-code chart (third-party copy of manufacturer service data)

Last reviewed: October 20, 2026. ErrorCodePro is not affiliated with GE.