Maytag Bravos or Centennial VMW top-load washer Error Code Wash LED on: Meaning & How to Fix It

By the ErrorCodePro Editorial Team · Last reviewed October 20, 2026

Maytag Bravos or Centennial VMW top-load washer error code Wash LED on means: No fill or long fill. [1] Keep using it? Only if the owner checks below clear the code; if it returns, stop and book a repair. Start with the owner checks below, beginning with: write down the code and model number.

Source: Maytag Bravos or Centennial VMW top-load washer error-code chart, via Sears PartsDirect [1].

Quick facts

Code	Wash LED on
Also shown as	None listed by the manufacturer
Brand / appliance	Maytag Bravos or Centennial VMW top-load washer
System	Water fill
Meaning (service chart)	No fill or long fill. [1]
Keep using it?	Only if the owner checks below clear the code; if it returns, stop and book a repair
DIY-safe?	Owner checks only (listed below)
Support	Maytag Product Help (producthelp.maytag.com), 1-800-344-1274
Source document	Maytag Bravos or Centennial VMW top-load washer error-code chart (via Sears PartsDirect)

On this page: Meaning · Steps · Parts · When to call a technician · Related codes · FAQ

What error code Wash LED on means on a Maytag Bravos or Centennial VMW top-load washer

No fill or long fill. [1]

This is a water fill code. Codes and wording can vary by model, so check your owner's manual for your model number.

How to fix Maytag Bravos or Centennial VMW top-load washer error code Wash LED on (safe owner checks)

Safety first: disconnect power before you remove any panel or reach into the sump or drum. Do not touch wiring, the control board or the motor. If you see water near electrical parts, stop and call a technician. These steps are based on the Maytag Bravos or Centennial VMW top-load washer error-code chart (via Sears PartsDirect) [1], rewritten for clarity.

Write down the code and model number. Note exactly what the display shows (Wash LED on) and copy the full model number from the rating label, so you can confirm this chart applies to your bravos or Centennial VMW top-load washer and order the right parts.
Check the fill hoses. Check the fill hoses and inlet water valves.
Do a power reset. Unplug the appliance or switch off its breaker for one minute, then restore power and try again. If the code clears and stays away, it may have been a one-off fault.
Test and decide. Run a short cycle or restart and watch the display. If Wash LED on comes back after these checks, stop using the washer for this function and call a technician, because the remaining causes need meters or part replacement.

The first and last steps (and the power reset) are general owner checks added by ErrorCodePro; the rest follow the Maytag Bravos or Centennial VMW top-load washer error-code chart published by Sears PartsDirect, rewritten for safe owner use.

Parts that may be involved

Exact parts depend on your model number. This page lists part types only, never part numbers.

Inlet water valve assembly
Main electronic control board

When to call a technician

If the inlet water valve assembly is defective, a technician should replace it.
If water is entering the machine but not being detected, then the main electronic control board (which includes the water level pressure switch) will usually need to be replaced.
Anything involving wiring, the control board, the motor or the water valve electrics
The appliance is under warranty: contact Maytag Product Help (producthelp.maytag.com), 1-800-344-1274 first

Frequently asked questions

What does error code Wash LED on mean on a Maytag Bravos or Centennial VMW top-load washer?

The Maytag Bravos or Centennial VMW top-load washer error-code chart lists Wash LED on as follows: No fill or long fill.

Is it safe to keep using the Bravos or Centennial VMW top-load washer with Wash LED on?

Only if the owner checks below clear the code; if it returns, stop and book a repair.

Can I fix Maytag Bravos or Centennial VMW top-load washer error Wash LED on myself?

Only with the owner checks on this page, starting with: write down the code and model number. If it persists, call a technician or Maytag Product Help (producthelp.maytag.com), 1-800-344-1274.

Sources

Sears PartsDirect: Maytag Bravos or Centennial VMW top-load washer error-code chart (third-party copy of manufacturer service data)

Last reviewed: October 20, 2026. ErrorCodePro is not affiliated with Maytag.