Maytag Compact front-load washer Error Code A09: Meaning & How to Fix It

By the ErrorCodePro Editorial Team · Last reviewed October 20, 2026

Maytag compact front-load washer error code A09 means: No water detected. [1] Keep using it? Only if the owner checks below clear the code; if it returns, stop and book a repair. Start with the owner checks below, beginning with: write down the code and model number.

Source: Maytag compact front-load washer error-code chart, via Sears PartsDirect [1].

Quick facts

Code	A09
Also shown as	F01
Brand / appliance	Maytag compact front-load washer
System	Drain
Meaning (service chart)	No water detected. [1]
Keep using it?	Only if the owner checks below clear the code; if it returns, stop and book a repair
DIY-safe?	Owner checks only (listed below)
Support	Maytag Product Help (producthelp.maytag.com), 1-800-344-1274
Source document	Maytag compact front-load washer error-code chart (via Sears PartsDirect)

On this page: Meaning · Steps · Parts · When to call a technician · Related codes · FAQ

What error code A09 means on a Maytag compact front-load washer

No water detected. [1]

This is a drain code. Codes and wording can vary by model, so check your owner's manual for your model number.

How to fix Maytag compact front-load washer error code A09 (safe owner checks)

Safety first: disconnect power before you remove any panel or reach into the sump or drum. Do not touch wiring, the control board or the motor. If you see water near electrical parts, stop and call a technician. These steps are based on the Maytag compact front-load washer error-code chart (via Sears PartsDirect) [1], rewritten for clarity.

Write down the code and model number. Note exactly what the display shows (A09) and copy the full model number from the rating label, so you can confirm this chart applies to your compact front-load washer and order the right parts.
Open the water supply. Make sure both water supply valves behind the washer are fully open.
Check the drain system. Check the drain system for a siphon problem.
Do a power reset. Unplug the appliance or switch off its breaker for one minute, then restore power and try again. If the code clears and stays away, it may have been a one-off fault.
Test and decide. Run a short cycle or restart and watch the display. If A09 comes back after these checks, stop using the washer for this function and call a technician, because the remaining causes need meters or part replacement.

The first and last steps (and the power reset) are general owner checks added by ErrorCodePro; the rest follow the Maytag compact front-load washer error-code chart published by Sears PartsDirect, rewritten for safe owner use.

Parts that may be involved

Exact parts depend on your model number. This page lists part types only, never part numbers.

Water valve assembly

When to call a technician

If the water valve assembly is defective, a technician should replace it.
Anything involving wiring, the control board, the motor or the water valve electrics
The appliance is under warranty: contact Maytag Product Help (producthelp.maytag.com), 1-800-344-1274 first

Frequently asked questions

What does error code A09 mean on a Maytag compact front-load washer?

The Maytag compact front-load washer error-code chart lists A09 as follows: No water detected.

Is it safe to keep using the compact front-load washer with A09?

Only if the owner checks below clear the code; if it returns, stop and book a repair.

Can I fix Maytag compact front-load washer error A09 myself?

Only with the owner checks on this page, starting with: write down the code and model number. If it persists, call a technician or Maytag Product Help (producthelp.maytag.com), 1-800-344-1274.

Is F01 the same as A09?

Yes. The source chart lists F01 with the same meaning as A09; the display format depends on the model.

Sources

Sears PartsDirect: Maytag compact front-load washer error-code chart (third-party copy of manufacturer service data)

Last reviewed: October 20, 2026. ErrorCodePro is not affiliated with Maytag.