Samsung WaterWall dishwasher Error Code bE2: Meaning & How to Fix It

By the ErrorCodePro Editorial Team · Last reviewed October 20, 2026

Samsung WaterWall dishwasher error code bE2 means: Stuck button on the control panel. [1] Keep using it? Only if the owner checks below clear the code; if it returns, stop and book a repair. Start with the owner checks below, beginning with: write down the code and model number.

Source: Samsung WaterWall dishwasher error-code chart, via Sears PartsDirect [1].

Quick facts

Code	bE2
Also shown as	None listed by the manufacturer
Brand / appliance	Samsung WaterWall dishwasher
System	Control / electronics
Meaning (service chart)	Stuck button on the control panel. [1]
Keep using it?	Only if the owner checks below clear the code; if it returns, stop and book a repair
DIY-safe?	Owner checks only (listed below)
Support	Samsung Support Center (samsung.com/us/support)
Source document	Samsung WaterWall dishwasher error-code chart (via Sears PartsDirect)

On this page: Meaning · Steps · Parts · When to call a technician · Related codes · FAQ

What error code bE2 means on a Samsung WaterWall dishwasher

Stuck button on the control panel. [1]

This is a control / electronics code. Codes and wording can vary by model, so check your owner's manual for your model number.

How to fix Samsung WaterWall dishwasher error code bE2 (safe owner checks)

Safety first: disconnect power before you remove any panel or reach into the sump or drum. Do not touch wiring, the control board or the motor. If you see water near electrical parts, stop and call a technician. These steps are based on the Samsung WaterWall dishwasher error-code chart (via Sears PartsDirect) [1], rewritten for clarity.

Write down the code and model number. Note exactly what the display shows (bE2) and copy the full model number from the rating label, so you can confirm this chart applies to your waterWall dishwasher and order the right parts.
Clear the code at the controls. Press all the buttons on the control panel to attempt to free the stuck key.
Do a power reset. Unplug the appliance or switch off its breaker for one minute, then restore power and try again. If the code clears and stays away, it may have been a one-off fault.
Test and decide. Run a short cycle or restart and watch the display. If bE2 comes back after these checks, stop using the dishwasher for this function and call a technician, because the remaining causes need meters or part replacement.

The first and last steps (and the power reset) are general owner checks added by ErrorCodePro; the rest follow the Samsung WaterWall dishwasher error-code chart published by Sears PartsDirect, rewritten for safe owner use.

Parts that may be involved

Exact parts depend on your model number. This page lists part types only, never part numbers.

Control panel

When to call a technician

If the key remains stuck, a technician should replace the control panel.
Anything involving wiring, the control board, the motor or the water valve electrics
The appliance is under warranty: contact Samsung Support Center (samsung.com/us/support) first

Frequently asked questions

What does error code bE2 mean on a Samsung WaterWall dishwasher?

The Samsung WaterWall dishwasher error-code chart lists bE2 as follows: Stuck button on the control panel.

Is it safe to keep using the WaterWall dishwasher with bE2?

Only if the owner checks below clear the code; if it returns, stop and book a repair.

Can I fix Samsung WaterWall dishwasher error bE2 myself?

Only with the owner checks on this page, starting with: write down the code and model number. If it persists, call a technician or Samsung Support Center (samsung.com/us/support).

Sources

Sears PartsDirect: Samsung WaterWall dishwasher error-code chart (third-party copy of manufacturer service data)

Last reviewed: October 20, 2026. ErrorCodePro is not affiliated with Samsung.