Thermador Masterpiece wall oven Error Code E032: Meaning & How to Fix It
By the ErrorCodePro Editorial Team · Last reviewed October 20, 2026
Thermador Masterpiece wall oven error code E032 means: 10 seconds of multiple keys being pushed. [1] Keep using it? Only if the owner checks below clear the code; if it returns, stop and book a repair. Start with the owner checks below, beginning with: write down the code and model number.
Source: Thermador Masterpiece wall oven error-code chart, via Sears PartsDirect [1].
Quick facts
| Code | E032 |
|---|---|
| Also shown as | None listed by the manufacturer |
| Brand / appliance | Thermador Masterpiece wall oven |
| System | Control / electronics |
| Meaning (service chart) | 10 seconds of multiple keys being pushed. [1] |
| Keep using it? | Only if the owner checks below clear the code; if it returns, stop and book a repair |
| DIY-safe? | Owner checks only (listed below) |
| Support | Thermador customer support (see your owner's manual) |
| Source document | Thermador Masterpiece wall oven error-code chart (via Sears PartsDirect) |
On this page: Meaning · Steps · Parts · When to call a technician · Related codes · FAQ
What error code E032 means on a Thermador Masterpiece wall oven
10 seconds of multiple keys being pushed. [1]
This is a control / electronics code. Codes and wording can vary by model, so check your owner's manual for your model number.
How to fix Thermador Masterpiece wall oven error code E032 (safe owner checks)
- Write down the code and model number. Note exactly what the display shows (E032) and copy the full model number from the rating label, so you can confirm this chart applies to your masterpiece wall oven and order the right parts.
- Clear the code at the controls. Press "Clear" and reprogram the oven settings.
- Clear any clog or debris. Clean and dry the glass touch panel. Restore power and see if the error clears.
- Do a power reset. Unplug the appliance or switch off its breaker for one minute, then restore power and try again. If the code clears and stays away, it may have been a one-off fault.
- Test and decide. Run a short cycle or restart and watch the display. If E032 comes back after these checks, stop using the range for this function and call a technician, because the remaining causes need meters or part replacement.
The first and last steps (and the power reset) are general owner checks added by ErrorCodePro; the rest follow the Thermador Masterpiece wall oven error-code chart published by Sears PartsDirect, rewritten for safe owner use.
Parts that may be involved
Exact parts depend on your model number. This page lists part types only, never part numbers.
- User interface
- Electronic control board
- Wire harness
When to call a technician
- If not, disconnect power to the oven again and check the wire harness connections between the electronic oven control board and the user interface.
- Reconnect any loose wires or replace the wire harness if damaged.
- If the wire connections are okay, a technician should replace the user interface.
- If the problem continues, a technician should replace the electronic oven control board.
- Anything involving wiring, the control board, the motor or the water valve electrics
- The appliance is under warranty: contact Thermador customer support (see your owner's manual) first
Related error codes
Frequently asked questions
What does error code E032 mean on a Thermador Masterpiece wall oven?
The Thermador Masterpiece wall oven error-code chart lists E032 as follows: 10 seconds of multiple keys being pushed.
Is it safe to keep using the Masterpiece wall oven with E032?
Only if the owner checks below clear the code; if it returns, stop and book a repair.
Can I fix Thermador Masterpiece wall oven error E032 myself?
Only with the owner checks on this page, starting with: write down the code and model number. If it persists, call a technician or Thermador customer support (see your owner's manual).
Sources
- Sears PartsDirect: Thermador Masterpiece wall oven error-code chart (third-party copy of manufacturer service data)
Last reviewed: October 20, 2026. ErrorCodePro is not affiliated with Thermador.