ErrorCodePro · Appliance Error CodesWhirlpool Duet high-efficiency front-load washer Error Code F: Meaning & How to Fix It
By the ErrorCodePro Editorial Team · Last reviewed October 20, 2026
Whirlpool Duet high-efficiency front-load washer error code F means: Not filling. [1] Keep using it? Only if the owner checks below clear the code; if it returns, stop and book a repair. Start with the owner checks below, beginning with: write down the code and model number.
Source: Whirlpool Duet high-efficiency front-load washer error-code chart, via Sears PartsDirect [1].
Quick facts
| Code | F |
|---|---|
| Also shown as | H |
| Brand / appliance | Whirlpool Duet high-efficiency front-load washer |
| System | Water fill |
| Meaning (service chart) | Not filling. [1] |
| Keep using it? | Only if the owner checks below clear the code; if it returns, stop and book a repair |
| DIY-safe? | Owner checks only (listed below) |
| Support | Whirlpool: 1-866-698-2538 |
| Source document | Whirlpool Duet high-efficiency front-load washer error-code chart (via Sears PartsDirect) |
On this page: Meaning · Steps · Parts · When to call a technician · Related codes · FAQ
What error code F means on a Whirlpool Duet high-efficiency front-load washer
Not filling. [1]
This is a water fill code. Codes and wording can vary by model, so check your owner's manual for your model number.
How to fix Whirlpool Duet high-efficiency front-load washer error code F (safe owner checks)
- Write down the code and model number. Note exactly what the display shows (F) and copy the full model number from the rating label, so you can confirm this chart applies to your duet high-efficiency front-load washer and order the right parts.
- Open the water supply. Make sure that both water supply valves behind the washer are fully open.
- Check the drain system. Check the drain system for a siphon problem.
- Do a power reset. Unplug the appliance or switch off its breaker for one minute, then restore power and try again. If the code clears and stays away, it may have been a one-off fault.
- Test and decide. Run a short cycle or restart and watch the display. If F comes back after these checks, stop using the washer for this function and call a technician, because the remaining causes need meters or part replacement.
The first and last steps (and the power reset) are general owner checks added by ErrorCodePro; the rest follow the Whirlpool Duet high-efficiency front-load washer error-code chart published by Sears PartsDirect, rewritten for safe owner use.
Parts that may be involved
Exact parts depend on your model number. This page lists part types only, never part numbers.
- Water inlet valve assembly
When to call a technician
- If the water inlet valve assembly is defective, a technician should replace it.,
- Anything involving wiring, the control board, the motor or the water valve electrics
- The appliance is under warranty: contact Whirlpool: 1-866-698-2538 first
Related error codes
Frequently asked questions
What does error code F mean on a Whirlpool Duet high-efficiency front-load washer?
The Whirlpool Duet high-efficiency front-load washer error-code chart lists F as follows: Not filling.
Is it safe to keep using the Duet high-efficiency front-load washer with F?
Only if the owner checks below clear the code; if it returns, stop and book a repair.
Can I fix Whirlpool Duet high-efficiency front-load washer error F myself?
Only with the owner checks on this page, starting with: write down the code and model number. If it persists, call a technician or Whirlpool: 1-866-698-2538.
Is H the same as F?
Yes. The source chart lists H with the same meaning as F; the display format depends on the model.
Sources
- Sears PartsDirect: Whirlpool Duet high-efficiency front-load washer error-code chart (third-party copy of manufacturer service data)
Last reviewed: October 20, 2026. ErrorCodePro is not affiliated with Whirlpool.