ErrorCodePro · Appliance Error CodesEdgeStar Laundry center Error Code E10: Meaning & How to Fix It
By the ErrorCodePro Editorial Team · Last reviewed October 20, 2026
EdgeStar laundry center error code E10 means: Water fill problem. The control detected that water level did not change for 7 minutes. [1] Keep using it? Only if the owner checks below clear the code; if it returns, stop and book a repair. Start with the owner checks below, beginning with: write down the code and model number.
Source: EdgeStar laundry center error-code chart, via Sears PartsDirect [1].
Quick facts
| Code | E10 |
|---|---|
| Also shown as | None listed by the manufacturer |
| Brand / appliance | EdgeStar laundry center |
| System | Water fill |
| Meaning (service chart) | Water fill problem. The control detected that water level did not change for 7 minutes. [1] |
| Keep using it? | Only if the owner checks below clear the code; if it returns, stop and book a repair |
| DIY-safe? | Owner checks only (listed below) |
| Support | EdgeStar customer support (see your owner's manual) |
| Source document | EdgeStar laundry center error-code chart (via Sears PartsDirect) |
On this page: Meaning · Steps · Parts · When to call a technician · Related codes · FAQ
What error code E10 means on an EdgeStar laundry center
Water fill problem. The control detected that water level did not change for 7 minutes. [1]
This is a water fill code. Codes and wording can vary by model, so check your owner's manual for your model number.
How to fix EdgeStar laundry center error code E10 (safe owner checks)
- Write down the code and model number. Note exactly what the display shows (E10) and copy the full model number from the rating label, so you can confirm this chart applies to your laundry center and order the right parts.
- Open the water supply. Make sure the water supply faucets behind the appliance are fully open.
- Check the fill hoses. Check the water fill lines for kinks or freezing (in the winter).
- Check the water inlet fill. Check the water inlet fill valves.
- Do a power reset. Unplug the appliance or switch off its breaker for one minute, then restore power and try again. If the code clears and stays away, it may have been a one-off fault.
- Test and decide. Run a short cycle or restart and watch the display. If E10 comes back after these checks, stop using the washer for this function and call a technician, because the remaining causes need meters or part replacement.
The first and last steps (and the power reset) are general owner checks added by ErrorCodePro; the rest follow the EdgeStar laundry center error-code chart published by Sears PartsDirect, rewritten for safe owner use.
Parts that may be involved
Exact parts depend on your model number. This page lists part types only, never part numbers.
- Water inlet valve assembly
When to call a technician
- If the valves don't open to fill the tub when activated, a technician should replace the water inlet valve assembly.
- Anything involving wiring, the control board, the motor or the water valve electrics
- The appliance is under warranty: contact EdgeStar customer support (see your owner's manual) first
Related error codes
Frequently asked questions
What does error code E10 mean on an EdgeStar laundry center?
The EdgeStar laundry center error-code chart lists E10 as follows: Water fill problem. The control detected that water level did not change for 7 minutes.
Is it safe to keep using the laundry center with E10?
Only if the owner checks below clear the code; if it returns, stop and book a repair.
Can I fix EdgeStar laundry center error E10 myself?
Only with the owner checks on this page, starting with: write down the code and model number. If it persists, call a technician or EdgeStar customer support (see your owner's manual).
Sources
- Sears PartsDirect: EdgeStar laundry center error-code chart (third-party copy of manufacturer service data)
Last reviewed: October 20, 2026. ErrorCodePro is not affiliated with EdgeStar.