ErrorCodePro · Appliance Error CodesEdgeStar Laundry center Error Code E56: Meaning & How to Fix It
By the ErrorCodePro Editorial Team · Last reviewed October 20, 2026
EdgeStar laundry center error code E56 means: Motor inverter control board drawing too much current. [1] Keep using it? Only if the owner checks below clear the code; if it returns, stop and book a repair. Start with the owner checks below, beginning with: write down the code and model number.
Source: EdgeStar laundry center error-code chart, via Sears PartsDirect [1].
Quick facts
| Code | E56 |
|---|---|
| Also shown as | E57 |
| Brand / appliance | EdgeStar laundry center |
| System | Motor / drive |
| Meaning (service chart) | Motor inverter control board drawing too much current. [1] |
| Keep using it? | Only if the owner checks below clear the code; if it returns, stop and book a repair |
| DIY-safe? | Owner checks only (listed below) |
| Support | EdgeStar customer support (see your owner's manual) |
| Source document | EdgeStar laundry center error-code chart (via Sears PartsDirect) |
On this page: Meaning · Steps · Parts · When to call a technician · Related codes · FAQ
What error code E56 means on an EdgeStar laundry center
Motor inverter control board drawing too much current. [1]
This is a motor / drive code. Codes and wording can vary by model, so check your owner's manual for your model number.
How to fix EdgeStar laundry center error code E56 (safe owner checks)
- Write down the code and model number. Note exactly what the display shows (E56) and copy the full model number from the rating label, so you can confirm this chart applies to your laundry center and order the right parts.
- Rebalance the load. Reduce the load if overloaded.
- Do a power reset. Unplug the appliance or switch off its breaker for one minute, then restore power and try again. If the code clears and stays away, it may have been a one-off fault.
- Test and decide. Run a short cycle or restart and watch the display. If E56 comes back after these checks, stop using the washer for this function and call a technician, because the remaining causes need meters or part replacement.
The first and last steps (and the power reset) are general owner checks added by ErrorCodePro; the rest follow the EdgeStar laundry center error-code chart published by Sears PartsDirect, rewritten for safe owner use.
Parts that may be involved
Exact parts depend on your model number. This page lists part types only, never part numbers.
- Motor inverter control board
- Drive motor
- Wire harness
When to call a technician
- If the load is normal size, unplug the appliance and check the wire harness connections between the motor inverter control board and drive motor.
- Reconnect any loose wires or replace the wire harness if damaged.
- If the wire connections are okay, a technician should replace the motor inverter control board.
- If the problem continues, a technician should replace the drive motor.
- Anything involving wiring, the control board, the motor or the water valve electrics
- The appliance is under warranty: contact EdgeStar customer support (see your owner's manual) first
Related error codes
Frequently asked questions
What does error code E56 mean on an EdgeStar laundry center?
The EdgeStar laundry center error-code chart lists E56 as follows: Motor inverter control board drawing too much current.
Is it safe to keep using the laundry center with E56?
Only if the owner checks below clear the code; if it returns, stop and book a repair.
Can I fix EdgeStar laundry center error E56 myself?
Only with the owner checks on this page, starting with: write down the code and model number. If it persists, call a technician or EdgeStar customer support (see your owner's manual).
Is E57 the same as E56?
Yes. The source chart lists E57 with the same meaning as E56; the display format depends on the model.
Sources
- Sears PartsDirect: EdgeStar laundry center error-code chart (third-party copy of manufacturer service data)
Last reviewed: October 20, 2026. ErrorCodePro is not affiliated with EdgeStar.