ErrorCodePro · Appliance Error Codes

Electrolux Compact condensing dryer Error Code Ex52: Meaning & How to Fix It

By the ErrorCodePro Editorial Team · Last reviewed October 20, 2026

Electrolux compact condensing dryer error code Ex52 means: Drive motor thermal cut-out tripped. The thermal cutout trips when the drive motor overheats. [1] Keep using it? Only if the owner checks below clear the code; if it returns, stop and book a repair. Start with the owner checks below, beginning with: write down the code and model number.

Source: Electrolux compact condensing dryer error-code chart, via Sears PartsDirect [1].

Quick facts

CodeEx52
Also shown asNone listed by the manufacturer
Brand / applianceElectrolux compact condensing dryer
SystemMotor / drive
Meaning (service chart)Drive motor thermal cut-out tripped. The thermal cutout trips when the drive motor overheats. [1]
Keep using it?Only if the owner checks below clear the code; if it returns, stop and book a repair
DIY-safe?Owner checks only (listed below)
SupportElectrolux support (owner.electrolux.com)
Source documentElectrolux compact condensing dryer error-code chart (via Sears PartsDirect)

On this page: Meaning · Steps · Parts · When to call a technician · Related codes · FAQ

What error code Ex52 means on an Electrolux compact condensing dryer

Drive motor thermal cut-out tripped. The thermal cutout trips when the drive motor overheats. [1]

This is a motor / drive code. Codes and wording can vary by model, so check your owner's manual for your model number.

How to fix Electrolux compact condensing dryer error code Ex52 (safe owner checks)

Safety first: disconnect power before you remove any panel or reach into the sump or drum. Do not touch wiring, the control board or the motor. If you see water near electrical parts, stop and call a technician. These steps are based on the Electrolux compact condensing dryer error-code chart (via Sears PartsDirect) [1], rewritten for clarity.
  1. Write down the code and model number. Note exactly what the display shows (Ex52) and copy the full model number from the rating label, so you can confirm this chart applies to your compact condensing dryer and order the right parts.
  2. Rebalance the load. Remove some of the load if too large or heavy.
  3. Do a power reset. Unplug the appliance or switch off its breaker for one minute, then restore power and try again. If the code clears and stays away, it may have been a one-off fault.
  4. Test and decide. Run a short cycle or restart and watch the display. If Ex52 comes back after these checks, stop using the dryer for this function and call a technician, because the remaining causes need meters or part replacement.

The first and last steps (and the power reset) are general owner checks added by ErrorCodePro; the rest follow the Electrolux compact condensing dryer error-code chart published by Sears PartsDirect, rewritten for safe owner use.

Parts that may be involved

Exact parts depend on your model number. This page lists part types only, never part numbers.

When to call a technician

Frequently asked questions

What does error code Ex52 mean on an Electrolux compact condensing dryer?

The Electrolux compact condensing dryer error-code chart lists Ex52 as follows: Drive motor thermal cut-out tripped. The thermal cutout trips when the drive motor overheats.

Is it safe to keep using the compact condensing dryer with Ex52?

Only if the owner checks below clear the code; if it returns, stop and book a repair.

Can I fix Electrolux compact condensing dryer error Ex52 myself?

Only with the owner checks on this page, starting with: write down the code and model number. If it persists, call a technician or Electrolux support (owner.electrolux.com).

Sources

  1. Sears PartsDirect: Electrolux compact condensing dryer error-code chart (third-party copy of manufacturer service data)

Last reviewed: October 20, 2026. ErrorCodePro is not affiliated with Electrolux.