ErrorCodePro · Appliance Error CodesKenmore 363 electronic control model dishwasher Error Code C6: Meaning & How to Fix It
By the ErrorCodePro Editorial Team · Last reviewed October 20, 2026
Kenmore 363 electronic control model dishwasher error code C6 means: Water temperature too low. [1] Keep using it? Only if the owner checks below clear the code; if it returns, stop and book a repair. Start with the owner checks below, beginning with: write down the code and model number.
Source: Kenmore 363 electronic control model dishwasher error-code chart, via Sears PartsDirect [1].
Quick facts
| Code | C6 |
|---|---|
| Also shown as | None listed by the manufacturer |
| Brand / appliance | Kenmore 363 electronic control model dishwasher |
| System | Heating |
| Meaning (service chart) | Water temperature too low. [1] |
| Keep using it? | Only if the owner checks below clear the code; if it returns, stop and book a repair |
| DIY-safe? | Owner checks only (listed below) |
| Support | Kenmore customer support (kenmore.com) or a Sears-authorized technician |
| Source document | Kenmore 363 electronic control model dishwasher error-code chart (via Sears PartsDirect) |
On this page: Meaning · Steps · Parts · When to call a technician · Related codes · FAQ
What error code C6 means on a Kenmore 363 electronic control model dishwasher
Water temperature too low. [1]
This is a heating code. Codes and wording can vary by model, so check your owner's manual for your model number.
How to fix Kenmore 363 electronic control model dishwasher error code C6 (safe owner checks)
- Write down the code and model number. Note exactly what the display shows (C6) and copy the full model number from the rating label, so you can confirm this chart applies to your 363 electronic control model dishwasher and order the right parts.
- Run the hot tap at. Run the hot tap at the kitchen sink for 1 minute and then fill a glass with the hot tap water.
- Check the settings. Adjust the water temperature setting in small increments to prevent scalding.
- Do a power reset. Unplug the appliance or switch off its breaker for one minute, then restore power and try again. If the code clears and stays away, it may have been a one-off fault.
- Test and decide. Run a short cycle or restart and watch the display. If C6 comes back after these checks, stop using the dishwasher for this function and call a technician, because the remaining causes need meters or part replacement.
The first and last steps (and the power reset) are general owner checks added by ErrorCodePro; the rest follow the Kenmore 363 electronic control model dishwasher error-code chart published by Sears PartsDirect, rewritten for safe owner use.
Parts that may be involved
Exact parts depend on your model number. This page lists part types only, never part numbers.
- Water temperature sensor
- Electronic control board
When to call a technician
- Measure the water temperature with an accurate thermometer.
- If the supply water temperature is normal, the temperature sensor or electronic control board might have failed.
- Anything involving wiring, the control board, the motor or the water valve electrics
- The appliance is under warranty: contact Kenmore customer support (kenmore.com) or a Sears-authorized technician first
Related error codes
Frequently asked questions
What does error code C6 mean on a Kenmore 363 electronic control model dishwasher?
The Kenmore 363 electronic control model dishwasher error-code chart lists C6 as follows: Water temperature too low.
Is it safe to keep using the 363 electronic control model dishwasher with C6?
Only if the owner checks below clear the code; if it returns, stop and book a repair.
Can I fix Kenmore 363 electronic control model dishwasher error C6 myself?
Only with the owner checks on this page, starting with: write down the code and model number. If it persists, call a technician or Kenmore customer support (kenmore.com) or a Sears-authorized technician.
Sources
- Sears PartsDirect: Kenmore 363 electronic control model dishwasher error-code chart (third-party copy of manufacturer service data)
Last reviewed: October 20, 2026. ErrorCodePro is not affiliated with Kenmore.