Kenmore 664 model electric slide-in range Error Code F9E0: Meaning & How to Fix It

By the ErrorCodePro Editorial Team · Last reviewed October 20, 2026

Kenmore 664 model electric slide-in range error code F9E0 means: Miswired power cord. When your range isn't heating, you may see an error code in the display. The error code will likely point you in the direction of the range failure. [1] Keep using it? Only if the owner checks below clear the code; if it returns, stop and book a repair. Start with the owner checks below, beginning with: write down the code and model number.

Source: Kenmore 664 model electric slide-in range error-code chart, via Sears PartsDirect [1].

Quick facts

Code	F9E0
Also shown as	None listed by the manufacturer
Brand / appliance	Kenmore 664 model electric slide-in range
System	Power supply
Meaning (service chart)	Miswired power cord. When your range isn't heating, you may see an error code in the display. The error code will likely point you in the direction of the range failure. [1]
Keep using it?	Only if the owner checks below clear the code; if it returns, stop and book a repair
DIY-safe?	Owner checks only (listed below)
Support	Kenmore customer support (kenmore.com) or a Sears-authorized technician
Source document	Kenmore 664 model electric slide-in range error-code chart (via Sears PartsDirect)

On this page: Meaning · Steps · Parts · When to call a technician · Related codes · FAQ

What error code F9E0 means on a Kenmore 664 model electric slide-in range

Miswired power cord. When your range isn't heating, you may see an error code in the display. The error code will likely point you in the direction of the range failure. [1]

This is a power supply code. Codes and wording can vary by model, so check your owner's manual for your model number.

How to fix Kenmore 664 model electric slide-in range error code F9E0 (safe owner checks)

Safety first: disconnect power before you remove any panel or reach into the sump or drum. Do not touch wiring, the control board or the motor. If you see water near electrical parts, stop and call a technician. These steps are based on the Kenmore 664 model electric slide-in range error-code chart (via Sears PartsDirect) [1], rewritten for clarity.

Write down the code and model number. Note exactly what the display shows (F9E0) and copy the full model number from the rating label, so you can confirm this chart applies to your 664 model electric slide-in range and order the right parts.
Clean the filter. Try our water filter finder Most common symptoms to help you fix your ranges Choose a symptom to see related range repairs.
Check the power supply. Unplug the range or shut off the house circuit breakers for the range to disconnect electrical power for 30 seconds, and then restore power to range. Unplug the range or shut off the house circuit breakers for the range to disconnect electrical power.
Test and decide. Run a short cycle or restart and watch the display. If F9E0 comes back after these checks, stop using the range for this function and call a technician, because the remaining causes need meters or part replacement.

The first and last steps (and the power reset) are general owner checks added by ErrorCodePro; the rest follow the Kenmore 664 model electric slide-in range error-code chart published by Sears PartsDirect, rewritten for safe owner use.

Parts that may be involved

Exact parts depend on your model number. This page lists part types only, never part numbers.

No specific part is implied by the manufacturer's guidance for this code.

When to call a technician

Unplug the range and check the power cord wire connection on the terminal block.
Connect the wires correctly to the terminal block as shown in the installation guide.
Main causes: power supply failure, blown thermal fuse, bad relay control board, damaged terminal block, wiring failure...
Main causes: broken broiler element, weak or broken broil burner igniter, control system failure, faulty temperature sen...
Main causes: power supply problem, control thermostat or electronic control board failure, broken element, bad burner ig...
Main causes: broken oven door lock assembly, wiring failure, electronic control board problem...
Anything involving wiring, the control board, the motor or the water valve electrics
The appliance is under warranty: contact Kenmore customer support (kenmore.com) or a Sears-authorized technician first

Frequently asked questions

What does error code F9E0 mean on a Kenmore 664 model electric slide-in range?

The Kenmore 664 model electric slide-in range error-code chart lists F9E0 as follows: Miswired power cord. When your range isn't heating, you may see an error code in the display. The error code will likely point you in the direction of the range failure.

Is it safe to keep using the 664 model electric slide-in range with F9E0?

Only if the owner checks below clear the code; if it returns, stop and book a repair.

Can I fix Kenmore 664 model electric slide-in range error F9E0 myself?

Only with the owner checks on this page, starting with: write down the code and model number. If it persists, call a technician or Kenmore customer support (kenmore.com) or a Sears-authorized technician.

Sources

Sears PartsDirect: Kenmore 664 model electric slide-in range error-code chart (third-party copy of manufacturer service data)

Last reviewed: October 20, 2026. ErrorCodePro is not affiliated with Kenmore.