ErrorCodePro · Appliance Error CodesKenmore 796 model top-load washer Error Code dL: Meaning & How to Fix It
By the ErrorCodePro Editorial Team · Last reviewed October 20, 2026
Kenmore 796 model top-load washer error code dL means: Lid lock failure. [1] Keep using it? Only if the owner checks below clear the code; if it returns, stop and book a repair. Start with the owner checks below, beginning with: write down the code and model number.
Source: Kenmore 796 model top-load washer error-code chart, via Sears PartsDirect [1].
Quick facts
| Code | dL |
|---|---|
| Also shown as | None listed by the manufacturer |
| Brand / appliance | Kenmore 796 model top-load washer |
| System | Door / lock |
| Meaning (service chart) | Lid lock failure. [1] |
| Keep using it? | Only if the owner checks below clear the code; if it returns, stop and book a repair |
| DIY-safe? | Owner checks only (listed below) |
| Support | Kenmore customer support (kenmore.com) or a Sears-authorized technician |
| Source document | Kenmore 796 model top-load washer error-code chart (via Sears PartsDirect) |
On this page: Meaning · Steps · Parts · When to call a technician · Related codes · FAQ
What error code dL means on a Kenmore 796 model top-load washer
Lid lock failure. [1]
This is a door / lock code. Codes and wording can vary by model, so check your owner's manual for your model number.
How to fix Kenmore 796 model top-load washer error code dL (safe owner checks)
- Write down the code and model number. Note exactly what the display shows (dL) and copy the full model number from the rating label, so you can confirm this chart applies to your 796 model top-load washer and order the right parts.
- Close the door or lid fully. Check for debris in the lid lock assembly that could prevent the lock mechanism from engaging.
- Do a power reset. Unplug the appliance or switch off its breaker for one minute, then restore power and try again. If the code clears and stays away, it may have been a one-off fault.
- Test and decide. Run a short cycle or restart and watch the display. If dL comes back after these checks, stop using the washer for this function and call a technician, because the remaining causes need meters or part replacement.
The first and last steps (and the power reset) are general owner checks added by ErrorCodePro; the rest follow the Kenmore 796 model top-load washer error-code chart published by Sears PartsDirect, rewritten for safe owner use.
Parts that may be involved
Exact parts depend on your model number. This page lists part types only, never part numbers.
- Lid lock/switch assembly
When to call a technician
- Unplug the washer and check the wiring connections on the lid lock/switch assembly.
- If you find no wiring problems, you usually need to replace the door lock/switch assembly.
- Anything involving wiring, the control board, the motor or the water valve electrics
- The appliance is under warranty: contact Kenmore customer support (kenmore.com) or a Sears-authorized technician first
Related error codes
Frequently asked questions
What does error code dL mean on a Kenmore 796 model top-load washer?
The Kenmore 796 model top-load washer error-code chart lists dL as follows: Lid lock failure.
Is it safe to keep using the 796 model top-load washer with dL?
Only if the owner checks below clear the code; if it returns, stop and book a repair.
Can I fix Kenmore 796 model top-load washer error dL myself?
Only with the owner checks on this page, starting with: write down the code and model number. If it persists, call a technician or Kenmore customer support (kenmore.com) or a Sears-authorized technician.
Sources
- Sears PartsDirect: Kenmore 796 model top-load washer error-code chart (third-party copy of manufacturer service data)
Last reviewed: October 20, 2026. ErrorCodePro is not affiliated with Kenmore.