ErrorCodePro · Appliance Error CodesKenmore 796 model top-load washer Error Code IE: Meaning & How to Fix It
By the ErrorCodePro Editorial Team · Last reviewed October 20, 2026
Kenmore 796 model top-load washer error code IE means: Washer fills slowly. [1] Keep using it? Only if the owner checks below clear the code; if it returns, stop and book a repair. Start with the owner checks below, beginning with: write down the code and model number.
Source: Kenmore 796 model top-load washer error-code chart, via Sears PartsDirect [1].
Quick facts
| Code | IE |
|---|---|
| Also shown as | None listed by the manufacturer |
| Brand / appliance | Kenmore 796 model top-load washer |
| System | Water fill |
| Meaning (service chart) | Washer fills slowly. [1] |
| Keep using it? | Only if the owner checks below clear the code; if it returns, stop and book a repair |
| DIY-safe? | Owner checks only (listed below) |
| Support | Kenmore customer support (kenmore.com) or a Sears-authorized technician |
| Source document | Kenmore 796 model top-load washer error-code chart (via Sears PartsDirect) |
On this page: Meaning · Steps · Parts · When to call a technician · Related codes · FAQ
What error code IE means on a Kenmore 796 model top-load washer
Washer fills slowly. [1]
This is a water fill code. Codes and wording can vary by model, so check your owner's manual for your model number.
How to fix Kenmore 796 model top-load washer error code IE (safe owner checks)
- Write down the code and model number. Note exactly what the display shows (IE) and copy the full model number from the rating label, so you can confirm this chart applies to your 796 model top-load washer and order the right parts.
- Open the water supply. Check the water supply faucets behind the washer to make , sure that they are fully open.
- Check the fill hoses. Check the fill hoses for kinks or freezing (in winter).
- Clear any clog or debris. Check the screens on the water inlet valves for debris or deposits.
- Do a power reset. Unplug the appliance or switch off its breaker for one minute, then restore power and try again. If the code clears and stays away, it may have been a one-off fault.
- Test and decide. Run a short cycle or restart and watch the display. If IE comes back after these checks, stop using the washer for this function and call a technician, because the remaining causes need meters or part replacement.
The first and last steps (and the power reset) are general owner checks added by ErrorCodePro; the rest follow the Kenmore 796 model top-load washer error-code chart published by Sears PartsDirect, rewritten for safe owner use.
Parts that may be involved
Exact parts depend on your model number. This page lists part types only, never part numbers.
- Water inlet valve assembly
When to call a technician
- Technician: replace the water inlet valve assembly if the water inlet screens are clogged.,
- Anything involving wiring, the control board, the motor or the water valve electrics
- The appliance is under warranty: contact Kenmore customer support (kenmore.com) or a Sears-authorized technician first
Related error codes
Frequently asked questions
What does error code IE mean on a Kenmore 796 model top-load washer?
The Kenmore 796 model top-load washer error-code chart lists IE as follows: Washer fills slowly.
Is it safe to keep using the 796 model top-load washer with IE?
Only if the owner checks below clear the code; if it returns, stop and book a repair.
Can I fix Kenmore 796 model top-load washer error IE myself?
Only with the owner checks on this page, starting with: write down the code and model number. If it persists, call a technician or Kenmore customer support (kenmore.com) or a Sears-authorized technician.
Sources
- Sears PartsDirect: Kenmore 796 model top-load washer error-code chart (third-party copy of manufacturer service data)
Last reviewed: October 20, 2026. ErrorCodePro is not affiliated with Kenmore.